Symetrix Radius NX 12x8 Audio Processor

Radius NX is equipped with 128 (64—64) redundant Dante channels. Dante protocol enables ultra-reliable multi-channel audio networking over IP. Together, Symetrix and Audinate's Dante provide the fastest possible way to implement, control, and maintain a system of networked DSPs and accessories - including third-party Dante-enabled end points.

Symetrix engineers, having worked with Dante for over ten years, leverage the protocol for box-to-box audio networking as well as peer-to-peer connection with major third-parties including AudioTechnica, Clockaudio, and Shure. In countless case studies, designers have benefited from the use of low cost off-the-shelf switches and cabling to link Symetrix DSPs with Dante-enabled mixing consoles, microphones, power amplifiers, loudspeakers, and computers.

Symetrix Radius NX Features

• 12 analog inputs, 8 analog outputs
• Optional AEC coprocessor module - up to 16 channels
• USB audio port enables soft-codecs + record/playback
• Dedicated routing resources for a 128—128 Super Matrix
• 4-port Gigabit Switch serves Dante + control networks
• Ultra-low noise preamps with 3 dB gain steps
• Support for Radius and Edge Expansion Cards

• Radius NX 12x8 Audio Processor1

• Processor1 x Analog Devices Griffin ADSP-SC587 dual- core DSP @ 500 MHz
• Raw processing capacity500 MIPS, 6 GFLOPS, 2 GMACS
• Sampling rate48 kHz, ± 100 ppm.
• Frequency response (A/D/A)20 Hz – 20 kHz, ± 0.5 dB.
• Dynamic range (A/D/A)> 114 dB, A-weighted.
• Channel separation (A/D/A) > 110 dB @ 1 kHz, +24 dBu
• Latency (A/D/A) 1.04 ms, inputs routed to outputs
• Delay memory 174 mono seconds.
• Analog control inputs 0-3.3 VDC.
• Recommended external control potentiometer 10k Ohm, linear.
• Logic outputs Low (0V) when active, pulled high (5V) when inactive.
• Logic output maximum external power supply voltage / current sinking24 VDC / 50 mA.
• Logic output maximum output current 10 mA.
• THD + Noise < -95 dB (22.4 kHz BW, unweighted); 1 kHz @ +15 dBu with 0 dB gain
• RS-232 accessory serial I/O 57.6 kbaud (default), 8 data bits, 1 stop bit, no parity, no flow control wired straight-through, only pins 2, 3, and 5 required
• RS-485 serial I/O 38.4 kbaud (default) 8 data bits, 1 stop bit, no parity, no flow control. May be broken out of ARC port
• Ethernet Cable Standard CAT5/6, maximum device to device length = 328 feet / 100 meters
• Dante Cable Standard CAT6, maximum device to device length = 328 feet / 100 meters
• ARC Cable Standard CAT5/6, distance dependent upon load and number of devices
• Maximum stored presets1000
• AEC (if installed)*
  • Number of Channels: Dual-core module: For standard conferencing, up to sixteen (16) channels with two (2) references. For mix-minus applications, up to eight (8) channels with eight (8) references. Single-core module: For standard conferencing, up to eight (8) channels with one (1) reference. For mix-minus applications, up to four (4) channels with four (4) references.
  • Tail Length: 400 mS maximum, dependent on channel and reference count
  • Convergence Rate: Typically > 90dB/sec
  • Latency: 11 mS
  • Processors: 1 x Analog Devices Griffin ADSP-21584 dual-core DSP @ 500 MHz
  • Raw processing capacity: 500 MIPS, 6 GFLOPS, 2 GMACS
  • *Optional coprocessor module required, single-core or dual-core models are available.
• Analog Inputs
  • Connectors: 3.81 mm terminal blocks.
  • Number of inputs: Four (4) switchable balanced mic or line level
  • Nominal input level: +4 dBu
  • Maximum input level: +24 dBu.
  • Mic pre-amp gain: 0 to 51 dB in 3 dB steps with ± 24 dB digital trim
  • Mic pre-amp EIN: < -125 dB with 150 Ohm source impedance, 22.4 kHz BW
  • CMRR: > 50 dB @ 1 kHz, unity gain
  • Input impedance: 2k Ohms balanced, 1k Ohms unbalanced
  • Phantom power (per input): +48 VDC @ 10 mA maximum.
  • Dynamic range: > 115 dB, A-weighted.
  • THD + Noise: < -100 dB (22.4 kHz BW, unweighted); 1 kHz @ +15 dBu with 0 dB gain.
  • Latency: 0.31 mS
• Analog Outputs
  • Connectors: 3.81 mm terminal blocks.
  • Number of outputs: Four (4) balanced line level
  • Nominal output level: +4 dBu with 20 dB of headroom
  • Maximum output level: +24 dBu (+22.8 dBu into a 2k Ohm minimum load)
  • Output impedance: 300 Ohms balanced, 150 Ohms unbalanced.
  • Dynamic range: > 117 dB, A-weighted.
  • THD + Noise: < -97 dB (22.4 kHz BW, unweighted); 1 kHz, 0 dB gain +8 dBu output
  • Latency: 0.65 mS.
• USB Audio I/O
  • Connector: One (1) high-retention Type B
  • Interface: 2.0 with Audio class 1.0 legacy modes
  • Capacity: 1x1 (echo cancelling speakerphone and non-echo cancelling speakerphone modes) - driverless, 2x2 line I/O mode - driverless, and 8x8 line I/O mode - driver included
  • Sample Rate: 48 kHz
  • Bit Depth: 16-bit, speakerphone modes; 16 or 24-bit, line modes
• Mechanical Data
  • Space Required: 1U (WDH: 18.91 in. x 9.5 in. x 1.72 in. / 48.02 cm x 24.13 cm x 4.37 cm). Depth does not include connector allowance. Allow at least 3 inches additional clearance for rear panel connections. Additional depth may be required depending upon your specific wiring and connections.
  • Electrical: 100-240 VAC, 50/60 Hz, 60 Watts maximum, universal input.
  • Ventilation: Maximum recommended ambient operating temperature is 30 C / 86 F. Ensure that the left and right equipment sides are unobstructed (5.08 cm, 2 in. minimum clearance). The ventilation should not be impeded by covering the ventilation openings with items such as newspapers, tablecloths, curtains, etc.
  • Shipping Weight: 8.5 lbs. (3.85 kg)
  • Certifications or Compliance: e Safety: UL 60065, cUL 60065, IEC 60065 EMC: EN 55103-1, EN 55103-2, EN55032, EN 61000-3-2, EN 61000-3-3, ICES-003, FCC Part 15 (all Class A) Environmental: RoHS