The CX Series is designed to meet the specialized needs of sound contractors. Eight 2-channel models have been designed from the ground up, combining the exclusive QSC PowerLight™ technology with specific features to meet the requirements of fixed installations. With high-output power, versatile loading options, high thermal capacity and unmatched reliability, the CX Series is the perfect solution to any permanently installed sound system.
QSC CX602V Features
- 8 models to meet your exact power requirements
- Three 70 volt direct models
- Five low impedance models, the CX902 and CX1102 also directly drive 70 volt loads
- Exclusive PowerLight switch-mode power supply technology for high performance and compact size
- Custom integrated security cover for tamper proof installations
- Variable speed fan for low noise
- 1 dB detented gain controls for fast and accurate gain settings
- Active inrush limiting eliminates AC inrush current, removing the need for expensive power sequencers
- XLR and detachable Euro style input connectors
- HD15 DataPort connector for Q-Sys and QSControl computer control and monitoring
- Dip switch control for clip limiters, high pass filters, bridge mono and parallel operation
- Selectable high pass filters protect speakers and prevent speaker transformer saturation withminimal effect on program material (33 Hz or 75 Hz on non-V models, 50 Hz or 75 Hz on V models)
- Comprehensive front panel indicators including signal, clip, protect and QSC's exclusive bridge mono and parallel input LEDs
- Barrier strip output connector
- Comprehensive protection circuitry including DC, infrasonic, thermal overload and short circuit protection
- Class H complementary bipolar output circuitry for high efficiency (CX702, CX902, CX1102 & CX1202V)
- Optional external transformer accessory pack for isolated 70 and 100 -volt outputs (converts CX302 to 400 watts per channel isolated output)
- Compact size - all models are only 2 rack units high and 14" deep for reduced rack cost and floor space
- Light weight - all models weigh only 21 pounds (9.5 kg) for easier racking and shipping
- CX602V 2-Channel 440W 70V Power Amplifier1
- POWER PER CHANNEL, STEREO MODE, Both Channels Driven
- 8Ω, 20 Hz–20 kHz, 0.05% THD: 550W
- 4Ω, 20 Hz–20 kHz, 0.05% THD: NA
- 2Ω, 1 kHz, 1% THD: NA
- 2Ω, 1 kHz, 1% THD: 400W
- 70 V, 1 kHz, 0.05% THD: 440W
- 70 V, 1 kHz, 1% THD: 600W
- POWER, BRIDGED MONO MODE
- 16Ω, 20 Hz–20 kHz, 0.1% THD: 1100W
- 8Ω, 20 Hz–20 kHz, 0.1% THD: NA
- 4Ω, 1 kHz, 1% THD: NA
- 140 V, 20 Hz–20 kHz, 0.05% THD: 800W
- 140 V, 1 kHz, 0.05% THD: 880W
- 140 V, 1 kHz, 1% THD: 1200W
- Noise, 20 Hz–20 kHz: -106dB
- Noise, 20 Hz–20 kHz: 1.26 Vrms
- Maximum Voltage Gain: 35dB
- Output Circuitry Class: AB+B
- Distortion (SMPTE-IM)Less than 0.02%
- Distortion (Typical) 20 Hz–20 kHz: 10 dB below rated powerLess than 0.01% THD
- 1.0 kHz and below: full rated powerLess than 0.01% THD
- Frequency Response20 Hz–20 kHz, ±0.2 dB
- Damping FactorGreater than 500
- Input Impedance6 kΩ unbalanced, 12 kΩ balanced
- Input Clipping10 V rms (+22 dBu)
- CoolingVariable-speed fan, rear-to-front air flow
- Connectors, each channel
- Input: 3-pin XLR & 3-pin detachable terminal blocks (1 each per channel)
- Output: Safety-shrouded barrier strip
- Amplifier Protection
- Full short circuit, open circuit, thermal, ultrasonic, and RF protection.
- Stable into reactive or mismatched loads.
- Load ProtectionOn/off muting, DC-fault power supply shutdown
- Dimensions (HWD)3.5 x 19 x 14 / 2RU inches (89 x 483 x 356 / 2RU mm)
- Weight
- 21 lb (9.5 kg) net
- 27 lb (12.3 kg) shipping
