This wireless lavalier microphone set consists of 2 x EW-DX SK (wireless bodypack transmitter), 2 x MKE 2 (omni-directional clip-on lavalier microphone), 1x EW-DX EM 2 rackmout receiver (2 channels) and 2 x BA 70 rechargeable batteries.
Available Configurations
- Q1-9: 470.2 - 550 MHz
- R1-9: 520 - 607.8 MHz
- V5-7: 941.7 - 951.8 MHz & 953.05 - 956.05 MHz & 956.65 - 959.65 MHz
Sennheiser EW-DX MKE 2 SET Features
- 2 channel half rack (9.5’)
- Up to 88 MHz switching bandwidth
- PoE IEEE 802.3af Class 3
- Equidistant Channel Spacing: 146 channels in standard mode; 293 channels in Link Density Mode
- Network enabled for control with Sennheiser Control Cockpit/media control system through a number of 3rd party modules
- Clear and easy focused user interface with OLED display
- Ethernet connectivity (IPv4 and IPv6)
- Secure AES 256 encryption
- External PSU 12V/1A
- All-metal housing
- 10mW RF power with up to 100m/328ft working range
- Charging contacts for in-device charging with CHG 70N
- Persistent eInk display - parameters visible on screen even when device is not powered on
- Programmable mute switch - customize the device depending on your professional needs
- Extended runtime with lithium ion batteries - up to 12 hours operation time
- Mic input trim control
- EW-DX EM 2 rack receiver1
- EW-DX SK bodypack transmitter2
- MKE 2 lavalier microphone2
- Rod antenna2
- Power supply with country adapters1
- Mic clamp2
- GA 3 rackmount set1
- Rubber feet4
- BA 70 rechargeable battery pack2
- System
- Audio Link Frequency Ranges
- Q1-6: 470.2 - 526 MHz
- R1-6: 520 - 576 MHz
- V5-7: 941.7 - 951.8 MHz & 953.05 - 956.05 MHz & 956.65 - 959.65 MHz
- Bluetooth® Low Energy (BLE) frequency range: 2402 - 2480 MHz
- Audio Frequency Response: 20 Hz - 20 kHz (-3 dB) @ 3 dBfs
- Audio THD: ≤ -60 dB for 1 kHz @ -3 dBfs input level
- Dynamic Range: 134 dB
- System Latency: 1.9 ms
- Operating Temperature: 14°F to 131°F (-10°C to 55°C)
- Relative Humidity: 5 - 95% (non-condensing)
- EW-DX EM 2 (rack receiver)
- Input Voltage: 11 - 13 V ⎓ or PoE IEEE 802.3af Class 0 (CAT5e or higher)
- Input Current: ≤ 1 A
- Transmit Power (radiated): BLE: max. 10 mW EIRP
- Audio Output Power: 18 dBu max
- Headphone Output: 2x 70 mW @ 32 Ω
- Ethernet
- RJ-45 socket, IEEE802.3
- 100Base-TX (half+full duplex)
- 10Base-T (half+full duplex)
- (CAT5e or higher)
- Dimensions: 8.35" x 1.73" x 7.44"
- Weight: approx. 2.2 pounds (without antennas and power supply)
- MKE 2 (lavalier microphone)
- Transducer Principle: pre-polarized condenser microphone
- Pick-Up Pattern: omnidirectional
- Sensitivity (free field, no load) (1kHz): 5 mV/Pa +- 3 dB
- Max. SPL at 1kHz: 142 dB
- Frequency Response: 20 to 20,000Hz
- Equivalent Noise Level A-weighted: 26 dB
- Connector: 3.5mm jack
- Cable Length: approx. 1.6m
- Supply Voltage: 7.5V
- EW-DX SK (bodypack transmitter)
- Input Voltage: 2.0 - 4.35 V
- Input Current: <300 mA
- Power Supply: 2 AA batteries 1.5 V (alkali manganese) or BA 70 rechargeable battery pack
- Occupied Bandwidth: 200 kHz
- Transmit Power (radiated)
- Audio link: 10 mW ERP
- (Range Y1-3: 12 mW ERP)
- LD mode: 10 mW ERP
- BLE: max. 10 mW EIRP
- Dimensions (without antenna): 2.5" x 3.35" x 0.79"
- Weight (without batteries): approx 0.27 pounds