null Skip to main content
QSC ISA300Ti 2-Channel 300W 70V/100V Power Amplifier
QSC ISA300Ti 2-Channel 300W 70/100V Power Amplifier

QSC ISA300Ti 2-Channel 300W 70/100V Power Amplifier

(No reviews yet)
SoundPro Item: 47570
Add to Wish List

Account manager
Have a Question? Ask an Account Manager

The ISA Installed System Amplifiers are designed to meet the needs of sound system designers and contractors worldwide. Three models feature isolated 25, 70, and 100 volt outputs for distributed sound systems, while four low impedance models are rated for 2 ohm operation. Versatile loading options and a comprehensive set of features make the ISA Series a rugged, cost-effective power solution for any permanently installed sound system.

QSC ISA300Ti Features

  • Low-impedance and isolated 25, 70, and 100 volt outputs for distributed audio systems available simultaneously
  • Rear panel gain controls for tamper resistant operation with 2 dB detents for quick and repeatable settings
  • XLR and detachable Euro style input connectors
  • DataPort V2 for use with DPV2-compatible signal processing accessories (XC-3, SF-3, LF-3) and DSP-3/DSP-4 (with external power supply)
  • Independent defeatable clip limiters for reduced distortion
  • Selectable high-pass filters protect speakers and prevent speaker transformer saturation with minimal effect on program material (50 Hz or 75 Hz)
  • Front panel indicators include power, signal, and clip
  • Covered barrier strip output connectors for safety agency compliance
  • Automatic variable-speed fan for quiet normal operation with maximum cooling on demand
  • Rear-to-front air flow keeps equipment racks cool
  • Stereo, Bridge, or Parallel operating modes
  • Comprehensive protection circuitry including DC, infrasonic, thermal overload and short circuit protection
  • Simple barrier strip connection determines output mode
  • QSC ISA300Ti 2-Channel 300W 70V/100V Power Amplifier1
  • Three-Year Warranty plus optional 3-year extended service contract1
  • OUTPUT POWER PER CHANNEL, STEREO MODE, both channels driven
    • 8Ω, 20 Hz–20 kHz 0.1% THD: 185W
    • 4Ω, 20 Hz–20 kHz 0.1% THD: 280W
    • 2Ω 1 kHz 1% THD: 430W
    • 8Ω, 1 kHz 0.1% THD: 600W
    • 4Ω 1 kHz 1% THD: 830W
  • Signal to Noise (20 Hz-20 kHz)100dB
  • Distortion (SMPTE-IM)Less than 0.01%
  • Input Sensitivity @ 8 ohms1.15V (+3.4 dBu)
  • Maximum Voltage Gain33.4× (30.5 dB)
  • Output CircuitryClass AB
  • THX ApprovedYes
  • Weight - Net44 lb (20.0 kg)
  • Weight - Shipping50 lb (22.7 kg)
  • Distortion (Typical) 20 Hz–20 kHz: 10 dB below rated powerLess than 0.03% THD, 4 ohms and 8 ohms
  • 1.0 kHz and below: full rated powerLess than 0.03% THD, 4 ohms and 8 ohms
  • Frequency Response 10 dB below rated output powerISA 300Ti, 500Ti and 800Ti: Direct outputs: -3 dB @ 50 Hz, -0.5 dB @ 20 kHz; XF outputs: 50 Hz–16 kHz, +1/-3 dB
  • Damping Factor with 8Ω Load (direct outputs)Greater than 200; ISA 1350 greater than 250
  • Output Regulation (isolated outputs)Less than 1.5 dB
  • Input Impedance10 kΩ unbalanced, 20 kΩ balanced
  • Input Clipping10 V rms (+22 dBu)
  • CoolingContinuously variable speed fan, back-to-front air flow
  • Connectors, each channel
    • Input: Active balanced; 3-pin Euro-style detachable terminal block and XLR (pin 2+)
    • Output: Covered barrier strips
    • DataPort V2: HD-15 connector
  • Controls
    • Front: AC switch
    • Rear: Ch. 1 and Ch. 2 gain knobs, 10-position DIP switch
  • Indicators
    • PWR-ON: Green LED; SIGNAL: Green LED (1 per channel);
    • CLIP: Red LED (1 per channel)
  • Dimensions (HWD) inches5.25 x 19 x 15.9 / 3RU
  • Dimensions (HWD) mm133 x 483 x 400 / 3RU
  • Amplifier Protection
    • Full short circuit, open circuit, thermal, ultrasonic, and RF protection;
    • Stable into reactive or mismatched loads
  • Power Requirements120 or 230 VAC, 50–60 Hz
  • Load ProtectionOn/off muting; Triac crowbar: ISA 750, 1350, and 800Ti; AC coupling: ISA 280, 300Ti, 450, and 500Ti

In The Box

Customer Reviews