Panasonic PT-RZ12KU 12,000 Lumen Large Venue Laser Projector

The compact Panasonic PT-RZ12KU 12,000 Lumen Large Venue Laser Projector is designed for long-lasting stable brightness in events and staging. Exchangeable lens - 24/7 Operation, Digital Link, High Frame Rate 120 Hz, Geometric Adjustment, Portrait Mode, Digital Link, 20 000:1.

Panasonic PT-RZ12KU Features

• Laser 3-chip DLP, 12000 lumens, WUXGA
• 120Hz high frame rate for superb and sharp motion pictures
• Lamp-free laser projection and dust resistant liquid cooling system with 20000 hours of free maintenance
• 20,000:1 contrast ratio

• PT-RZ12KU 12,000 Lumen Large Venue Laser Projector1

• Brightness 12,000 lumens
• Resolution 1,920 x 1,200 pixels (Input signals that exceed this resolution will be converted to 1,920 x 1,200 pixels.)
• Lamp 3-Chip DLP Laser
• Power supply AC 100-240 V 50/60 Hz
• Power consumption
  • 1,200 W (1,280 VA) (0.3 W with STANDBY MODE set to ECO. 4 W with STANDBY MODE set to NORMAL.), Average power consumption
  • NORMAL: 800W ECO: 680W LONG LIFE1: 620W LONG LIFE 2: 590W
  • LONG LIFE 3: 550W
  • *Operating Temperature: 25 °C (77 °F), Altitude: 700m (22 ft 12 in),
  • ICE627087: 2008 Broadcast contents, Picture mode: Dynamic, Dynamic Contrast[3]
• BTU value Max 4,096 BTU
• DLP™ chip | Panel size 24.4 mm (0.96 inches) diagonal (16:10 aspect ratio)
• DLP™ chip | Display method DLP™ chip x 3 (R, G, B), DLP™ projection system
• DLP™ chip | Pixels 2,304,000 (1,920 x 1,200) x 3, total of 6,912,000 pixels
• LENS Optional powered zoom/focus lenses
• Light source
  • Laser Diode (Laser class: Class 1)
  • Luminance life for set: 20,000 hours at half luminance (normal)/24,000 hours at half luminance (Eco)
  • * Temperature: 35°C (95°F), Altitude 700m (22ft 12in), Dust: 0.15mg/m³
  • 43,800 hours at constant luminance (Longlife[1])
  • 61,320 hours at constant luminance (Longlife[2])
  • 87,600 hours at constant luminance (Longlife[3])
• Screen size
  • 1.78-25.4 m (70-1,000 inches) (16:10 aspect ratio)
  • 1.78-15.24 m (70-600 inches) with the ET-D75LE8 (16:10 aspect ratio)
  • 3.05-15.24 m (120-600 inches) with the ET-D75LE90 (16:10 aspect ratio)
• Center-to-corner uniformity 90%
• Contrast 20,000:1 (full on/full off, in Dynamic Contrast 3 mode)
• Scanning frequency | SDI
  • SD-SDI signal (YCBCR 4:2:2 10-bit): SMPTE ST 259 compliant: 525i(480i), 625i(576i)
  • Single-link HD-SDI signal (YPBPR 4:2:2 10-bit): SMPTE ST 292 compliant: 750(720)/60p, 750(720)/50p, 1125(1035)/60i, 1125(1080)/60i, 1125(1080)/50i, 1125(1080)/25p, 1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p
  • Dual-link HD-SDI signal (RGB 4:4:4 12-bit/10-bit): SMPTE ST 372 compliant: 1125(1080)/60i, 1125(1080)/50i, 1125(1080)/25p, 1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p
  • 2048 x 1080/24p, 2048 x 1080/24sF, Dual-link HD-SDI signal (X Y Z 4:4:4 12-bit): SMPTE ST 372 compliant: 2048 x 1080/24p, 2048 x 1080/24sF, 3G-SDI signal (YPBPR 4:2:2 10-bit): SMPTE ST 424 compliant: 1125(1080)/60p, 1125(1080)/50p
  • 3G-SDI signal (RGB 4:4:4 12-bit/10-bit): SMPTE ST 424 compliant: 1125(1080)/60i, 1125(1080)/50i, 1125(1080)/25p, 1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p
  • Dual-link 3G-SDI signal (YPBPR 4:4:4 12-bit/10-bit): SMPTE ST 425 compliant: 1125(1080)/60i, 1125(1080)/50i, 2048 x 1080/48p, 2048 x 1080/50p, 2048 x 1080/60p
  • Dual-link 3G-SDI signal (RGB 4:4:4 12-bit/10-bit): SMPTE ST 425 compliant: 1125(1080)/60i, 1125(1080)/50i, 2048 x 1080/48p, 2048 x 1080/50p, 2048 x 1080/60p
• Scanning frequency | HDMI/DVI-D Horizontal: 15 kHz-100 kHz, vertical: 24 Hz - 120 Hz, dot clock: 25 MHz - 162 MHz
• Scanning frequency | RGB Horizontal: 15 kHz-100 kHz, vertical: 24 Hz - 120 Hz, dot clock: 162 MHz or less
• Scanning frequency | YPBPR (YCBCR)525i (480i): fH 15.73 kHz; fV 59.94 Hz, 625i (576i): fH 15.63 kHz; fV 50 Hz, 525p (480p): fH 31.47 kHz; fV 59.94 Hz, 625p (576p): fH 31.25 kHz; fV 50 Hz, 750 (720)/60p: fH 45.00 kHz; fV 60 Hz, 750 (720)/50p: fH 37.50 kHz; fV 50 Hz, 1125 (1035)/60i: fH 33.75 kHz; fV 60 Hz, 1125 (1080)/60i: fH 33.75 kHz; fV 60 Hz, 1125 (1080)/50i: fH 28.13 kHz; fV 50 Hz, 1125 (1080)/25p: fH 28.13 kHz; fV 25 Hz, 1125 (1080)/24p: fH 27.00 kHz; fV 24 Hz, 1125 (1080)/24sF: fH 27.00 kHz; fV 48 Hz, 1125 (1080)/30p: fH 33.75 kHz; fV 30 Hz, 1125 (1080)/60p: fH 67.50 kHz; fV 60 Hz, 1125 (1080)/50p: fH 56.25 kHz; fV 50 Hz
• Scanning frequency | Video/Y/C
  • fH: 15.73 kHz, fV: 59.94 Hz [NTSC/NTSC4.43/PAL-M/PAL60]
  • fH: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM]
• Optical axis shift | Vertical ±55% (±44% with the ET-D75LE6), (+73-78% with the ET-D75LE90), from center of screen, powered
• Optical axis shift | Horizontal
  • ±20% (±15% with the ET-D75LE6), (±6% with the ET-D75LE90), from center of screen, powered
  • NOTE: Optical axis shift function cannot be operated when used with the ET-D75LE50
• Keystone correction rangeVertical : ±40° (±22° with the ET-D75LE50, ±28° with the ET-D75LE6, +5° with the ET-D75LE90), Horizontal: ±15° (0° with the ET-D75LE90)
• Installation Ceiling/floor, front/rear
• Terminals | SDI IN 1
  • BNC x 2
  • Dual-link 3G-SDI signal: SMPTE ST 425 compliant
  • 3G-SDI (3G/HD/SD-SDI, Dual-link HD-SDI, Dual-link 3G-SDI)
  • Signal: SMPTE ST 424 compliant
  • Dual-link HD-SDI signal: SMPTE ST 372 compliant
  • HD-SDI signal: SMPTE ST 292 compliant
  • SD-SDI signal: SMPTE ST 259 compliant
• Terminals | HDMI INHDMI 19-pin x 1, Deep Color, compatible with HDCP, NOTE: Compatible with non-interlaced signals only.
• Terminals | DVI-D IN DVI-D 24-pin x 1, DVI 1.0 compliant, HDCP compatible, for single link only
• Terminals | RGB 1 IN BNC x 5
• Terminals | RGB 1 IN | R, G, B
  • R: 0.7 Vp-p, 75 ohms, G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms, B: 0.7 Vp-p, 75 ohms
  • HD, VD/SYNC: TTL, high impedance, positive/negative automatic
  • NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals
• Terminals | RGB 1 IN | Y, PB, PR (Y, CB, CR) Y: 1.0 Vp-p (including sync signal), PB/PR(CB/CR): 0.7 Vp-p, 75 ohms
• Terminals | RGB 1 IN | Video in
  • BNC x 1, 1.0 Vp-p 75 ohms
  • Y/C Y: 1.0 Vp-p (including sync signal), C: 0.286 Vp-p, 75 ohms
• Terminals | RGB 2 IN D-sub HD 15-pin (female) x 1
• Terminals | RGB 2 IN | R, G, B
  • R: 0.7 Vp-p, 75 ohms, G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms, B: 0.7 Vp-p, 75 ohms
  • HD, VD/SYNC: TTL, high impedance, positive/negative automatic
• Terminals | RGB 2 IN | Y, PB, PR (Y, CB, CR) Y: 1.0 Vp-p (including sync signal), PB/PR (CB/CR): 0.7 Vp-p, 75 ohms
• Terminals | 3D SYNC 1 IN/OUT
  • BNC x 1, 1.0 Vp-p, 75 ohms
  • Input: TTL, high impedance. Output: TTL, max. 10 mA
• Terminals | 3D SYNC 2 OUT BNC x 1, 1.0 Vp-p, 75 ohms, TTL, max. 10 mA
• Terminals | SERIAL IN D-sub 9-pin (female) x 1 for external control (RS-232C compliant)
• Terminals | SERIAL OUT D-sub 9-pin (male) x 1 for link control
• Terminals | Remoter 1 In M3 jack x 1 for wired remote control
• Terminals | Remoter 1 Out M3 jack x 1 for link control
• Terminals | Remoter 2 In D-sub 9-pin x 1 for external control (parallel)
• Terminals | DIGITAL LINK/LAN RJ-45 Network connection / digital link connection (video/network/serial control) compliant with PJLink™,100base-tx, Art-Net compatible
• Power cord length9 feet 10 inches (3 m)
• Cabinet materials Molded plastic
• Dimensions (WxHxD)22-3/4x12-23/32x29-1/8" (578x323.5x740 mm), without lens
• Weight97 lbs (44 kg), without lens
• Operating noise43 dB
• Operating temperature
  • Normal
  • The operating temperature range is 0°C to 50°C (32 °F to 122 °F).
  • (Brightness is limited at operating temperatures of 35°C (95°F) or more at altitudes from 700 m to 2,700 m (2,297 ft to 8,858 ft) above sea level,and at operating temperatures of 25°C (77°F) or more at altitudes from 2,700 m to 4,200 m (8,858 ft to 13,780 ft) above sea level.)
  • Eco/Long life 1/2/3
  • The operating temperature range is 0°C to 45°C (32 °F to 113 °F).
  • (Brightness is limited at operating temperatures of 35°C (95°F) or more at altitudes up to 2,700 m (8,858 ft) above sea level. The projector cannot be used at altitudes of 2,700 m (8,858 ft) or more above sea level.)
  • When the projector is used with a Smoke Cut Filter
  • The operating temperature range is 0°C to 40°C (32 °F to 104 °F).
  • (The projector cannot be used at altitudes of 1,400 m (4,593 ft) or more above sea level.)
  • * The brightness of the light source may drop depending on the operating temperature range. The higher the temperture, the greater the drop in the brightness of the light source will be.
• Applicable software 10%-80% (no condensation)
• Technology3-chip DLP Laser
• Notes
  • (1) Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
  • (2) Maximum physical resolution. Quad Pixel Drive: ON.
  • (3) Measured at center area of projector screen. Measurement method is in compliance with ISO/IEC 21118: 2012 international standards. Value is average of all products when shipped.
  • (4) With lens other than ET-D75LE95 and power supply of AC 200 V.